Generate square wave pulses at regular intervals
The Pulse Generator block generates square wave pulses at regular intervals. The block waveform parameters, Amplitude, Pulse Width, Period, and Phase delay, determine the shape of the output waveform. The following diagram shows how each parameter affects the waveform.
The Pulse Generator can emit scalar, vector, or matrix signals of any real data type. To cause the block to emit a scalar signal, use scalars to specify the waveform parameters. To cause the block to emit a vector or matrix signal, use vectors or matrices, respectively, to specify the waveform parameters. Each element of the waveform parameters affects the corresponding element of the output signal. For example, the first element of a vector amplitude parameter determines the amplitude of the first element of a vector output pulse. All the waveform parameters must have the same dimensions after scalar expansion. The data type of the output is the same as the data type of the Amplitude parameter.
This block output can be generated in time-based or sample-based modes, determined by the Pulse type parameter.
In time-based mode, Simulink® computes the block output
only at times when the output actually changes. This approach results
in fewer computations for the block output over the simulation time
period. Activate this mode by setting the Pulse type parameter
The block does not support a time-based configuration that results in a constant output signal. Simulink returns an error if the parameters Pulse Width and Period satisfy either of these conditions:
Depending on the pulse waveform characteristics, the intervals between changes in the block output can vary. For this reason, a time-based Pulse Generator block has a variable sample time. The sample time color of such blocks is brown (see View Sample Time Information for more information).
Simulink cannot use a fixed-step solver to compute the output of a time-based pulse generator. If you specify a fixed-step solver for models that contain time-based pulse generators, Simulink computes a fixed sample time for the time-based pulse generators. Then the time-based pulse generators simulate as sample based.
If you use a fixed-step solver and the Pulse type is
Time based, choose the step size such
that the period, phase delay, and pulse width (in seconds) are integer
multiples of the solver step size. For example, suppose that the period
4 seconds, the pulse width is
3 s), and the phase delay is
In this case, the computed sample time is
Therefore, choose a fixed-step size of
1 or a
number that divides
1 exactly (e.g.,
You can guarantee this by setting the fixed-step solver step size
auto on the Solver pane
of the Configuration Parameters dialog box.
In sample-based mode, the block computes its outputs at fixed
intervals that you specify. Activate this mode by setting the Pulse
type parameter to
An important difference between the time-based and sample-based modes is that in time-based mode, the block output is based on simulation time, and in sample-based mode, the block output depends only on the simulation start, regardless of elapsed simulation time. For more information, see the example Difference Between Time-Based and Sample-Based Pulse Generation Modes.
This block supports reset semantics in sample-based mode. For example, if a Pulse Generator is in a resettable subsystem that hits a reset trigger, the block output resets to its initial condition.
The Pulse Generator block outputs real signals of any numeric data type that Simulink supports, including fixed-point data types. The data type of the output signal is the same as that of the Amplitude parameter.
For more information, see Data Types Supported by Simulink in the Simulink documentation.
The pulse type for this block:
Time based or
based. The default is
Specifies whether to use simulation time or an external signal as the source of values for the output pulse's time variable. If you specify an external source, the block displays an input port for connecting the source. The output pulse differs as follows:
Use simulation time: The
block generates an output pulse where the time variable equals the
Use external signal: The
block generates an output pulse where the time variable equals the
value from the input port, which can differ from the simulation time.
The pulse amplitude. The default is
The pulse period specified in seconds if the pulse type is time-based
or as number of sample times if the pulse type is sample-based. The
The duty cycle specified as the percentage of the pulse period
that the signal is on if time-based or as number of sample times if
sample-based. The default is
The delay before the pulse is generated specified in seconds
if the pulse type is time-based or as number of sample times if the
pulse type is sample-based. The default is
The length of the sample time for this block in seconds. This parameter appears only if the block's pulse type is sample-based. See Specify Sample Time in the Simulink User's Guide for more information.
If you select this check box and the other parameters are one-row or one-column matrices, after scalar expansion, the block outputs a 1-D signal (vector). Otherwise the output dimensionality is the same as that of the other parameters. See Determining the Output Dimensions of Source Blocks.
The following Simulink examples show how to use the Pulse Generator block:
This example shows the difference in the behavior of the Pulse Generator block in time-based and sample-based modes.
Consider a model with two Pulse Generator blocks. In one block,
the Pulse type parameter is set to
based. In the other block, it is set to
based. Both blocks are set up to output a Boolean pulse
of 10 seconds: 5 seconds
on followed by 5 seconds
The simulation runs for 15 seconds from a start time of 3 seconds
to a stop time of 18 seconds, specified in the Model Configuration
Parameters dialog box. The figure shows the block diagram for this
model and the simulation output in the Scope block.
You can see
that simulation output starts at 3 seconds, as expected. Notice that
the time-based Pulse Generator produces a logical
only 2 seconds, after which its output changes to
t = 5 seconds. This is because this block starts computing its output
from t = 0 seconds, even though it doesn't output it until
the simulation starts at t = 3 seconds. The time-based block depends
on simulation time for its output.
The sample-based block outputs a pulse of 5 seconds
by 5 seconds
off. In this case, the blocks output
does not depend on simulation time, and starts only when the simulation
You cannot tune the value of the Phase delay parameter during simulation. As a workaround, you can add a Constant block and a Variable Time Delay block.
In the Pulse Generator block, set the value of
the Phase delay parameter to
Use the Constant block to specify the delay time (in
To tune the delay time during simulation, change the value stored in the Constant block.
Double | Single | Boolean | Base Integer | Fixed-Point