To implement the features in the Communications Toolbox™ Support Package for Xilinx® Zynq®-Based Radio, you must configure the host computer and the radio hardware for proper communication. After the support package is installed, follow these steps to manually set up the hardware.
To set up your hardware with a configuration that allows you to run models or scripts based on features released before R2018b, check all highlighted Compatibility with Previous Releases sections on this page. Note that this configuration option will be removed in a future release. Consider updating your designs based on features released before R2018b. For more information on this process, see Compatibility with Previous Releases.
Use this list to confirm that you have all required hardware and accessories to complete the hardware setup.
This connection is often referred to as a network connection. You can use either an integrated network interface card (NIC) with a Gigabit Ethernet cable or a USB 3.0 Gigabit Ethernet adapter dongle. This connection is necessary for transmitting data, such as a programming file, from the host computer to the radio hardware. It is also necessary for sending and receiving signals to and from the radio hardware.
Ethernet connection is the only supported method for connecting the radio hardware and host computer.
To have simultaneous Internet access in the absence of a wireless connection, the host computer must have two Ethernet connections.
If the host machine does not have an integrated card reader, use an external USB SD card reader.
For a list of supported radio hardware, see Hardware Support. Do not connect or turn on the device until you are prompted at a later step.
You need this cable to connect the radio hardware to the host.
You need antennas for transmitting and receiving signals over the air.
To work with the support package in MATLAB®, you must create a radio object for your radio hardware. In the following
dev is a radio object interfacing the AD936x-based radio hardware.
For an FMCOMMS5 radio hardware, you must call
'FMCOMMS5' instead of
dev = sdrdev('AD936x');
To set up your hardware with a configuration that allows you to run models or scripts based on features released before R2018b, create a radio object specific to your radio hardware that was released before R2018b. For example:
dev = sdrdev('ADI RF SOM');
sdrdev also sets up architecture-specific environment variables for
the radio hardware. These variables enable communication between MATLAB or Simulink® and the radio hardware.
For more information on creating radio objects, see
To connect the radio hardware to the host, you must configure an available network connection for it on the host. Follow the steps outlined for your specific operating system.
You need an SD memory card that is configured with the firmware of this support package. The firmware includes the embedded software and the FPGA programming file necessary for using the radio hardware as an I/O peripheral. If you have already configured an SD card with this image, skip this step.
Insert a 4 GB or larger SD memory card into the memory card reader on the host computer.
If the SD card is lockable, you must unlock it first.
At the MATLAB command prompt, enter the following command:
downloadImage(dev,'BoardName',DeviceName, ... 'SDCardLocation',SDCardDrive)
To set up your hardware with a configuration that allows you to run models or scripts based on features released before R2018b, use the following command instead:
dev — Radio object created using the
sdrdev function in Step 2. Set Up Support Package in MATLAB.
DeviceName — Name of the Zynq radio hardware, specified as a character vector.
dev is a radio object interfacing an AD936x-based radio
hardware, specify the board name as one of these options:
'ADI RF SOM'
'ZC706 and FMCOMMS2/3/4'
'ZCU102 and FMCOMMS2/3/4'
'ZedBoard and FMCOMMS2/3/4'
dev is a radio object interfacing an FMCOMMS5 radio
hardware, specify the board name as
'ZC706 and FMCOMMS5'.
SDCardDrive — Name of the SD card drive on the host
computer, specified as a character vector. For example,
dev = sdrdev('AD936x'); downloadImage(dev,'BoardName','ADI RF SOM', ... 'SDCardLocation','S:')
Before you can verify the setup, you must start the radio hardware properly. Wait until the radio hardware is ready as indicated in the previous step.
Check host-radio communication by calling the
function. When calling
testConnection, use the radio object that you
created in Step 2. Set Up Support Package in MATLAB
and the host IP address that you configured in Step 3. Configure Host Computer.
If the function returns all tests passed, then the host is communicating successfully with the radio hardware.
## Pinging host IP address ## Pinging radio IP address ## Checking compatibility of software with hardware ## Establishing connection to hardware. This process can take several seconds. ## Testing data path from Zynq board to host ## Establishing connection to hardware. This process can take several seconds. ## Waveform transmission has started successfully and will repeat indefinitely. ## Call the release method to stop the transmission. ## Establishing connection to hardware. This process can take several seconds. ## All tests PASSED.
Continue with one of the following options.
If the function returns a timeout or other error, then the host is not communicating with the radio hardware.
Warning: There was no response from the hardware. Read the documentation on how to diagnose connectivity issues. - Ensure the host and hardware are physically connected via GigE. - Ensure the host NIC is configured properly. - Check that the IPAddress of the hardware is specified correctly.
Return to Step 5. Connect Radio Hardware. Before calling the
info function, make sure that the radio hardware is properly
connected to the host. If you still have trouble, check Common Problems and Fixes.