Answered
FMCW radar for dynamic multitarget detection in matlab using triangular and sawtooth waveforms ?
There are several examples in Phased Array System Toolbox on automotive radar using FMCW and similar waveforms. You can find the...

7 years ago | 0

Answered
How we can give Delay in a clock ?
delayseq works on a vector, e,g., >> delayseq([1;0;1;0;1;0;1;0;1;0],0.004,250) >> ans = 0 1 0 1...

7 years ago | 0

| accepted

Answered
Difference between size '[:140 x 1]' and 'size [140 x 1]'
I assume this is what you get in your code generation report? [:140x1] means that the signal is a column vector with an upper bo...

7 years ago | 0

Answered
Real-time Spectrum Analysis
You can use Spectrum Analyzer to do this. https://www.mathworks.com/help/dsp/ref/dsp.spectrumanalyzer-system-object.html ...

7 years ago | 2

| accepted

Answered
units of waveforms phased array system toolbox
Yes, you can think of it as volts. The dB is always defined as 10*log10(W). HTH

7 years ago | 0

| accepted

Answered
Several targets in phased.TwoRayChannel
From the surface, I would say MeanRCS needs to be made to a 1x2M vector as you outlined, but GroundReflectionCoefficient propert...

7 years ago | 0

Answered
Definition of ground reflection coefficient in phased.Tworaychannel
This is a valid equation and it could work. Since this is for parallel incidence, i.e., the signal is in the incidence plane, yo...

7 years ago | 0

| accepted

Answered
Using a meshgrid or vector inside all function
You need to put global a in your cost function too. See the example in <https://www.mathworks.com/help/matlab/ref/g...

7 years ago | 1

| accepted

Answered
How do I configure a partitioned array into 4 quadrants where I can feed each quadrant to a receiver to feed amonopulse rat-race hybrid to get Sum and difference Az and El.
If you specify the array in a phased.Collector or phased.WidebandCollector, you will be able to access the output signal at each...

7 years ago | 0

| accepted

Answered
Use griddedInterpolant in MATLAB Function / Alternative to Simulink Functions in For Each Subsystem?
For the first question, the following link shows all supported functions for code generation and griddedInterpolant is not in it...

7 years ago | 1

Answered
Ho we run a section code one time in Matlab function block ? In below body I dont want assigning zeros in Dout after 1st iteration. This matlab function block run 100 times and problem is it every time set zeros in dout.
Do you get an error? What is the error message? Looks like you may have some dimension issues? An alternative way is to control ...

7 years ago | 0

Answered
Unable to compute kalman filter innovation (measurement residuals) in the new sensor fusion and tracking toolbox
Are you using trakingEKF? <https://www.mathworks.com/help/fusion/ref/trackingekf-class.html> There is a residual method yo...

7 years ago | 0

Answered
Ho we run a section code one time in Matlab function block ? In below body I dont want assigning zeros in Dout after 1st iteration. This matlab function block run 100 times and problem is it every time set zeros in dout.
You can make Dout persistent so it preserves the value between runs, like this persistent Dout; if isempty(Dout) Do...

7 years ago | 0

| accepted

Answered
Bandwidth of a chirp signal
I think the two questions are the same, essentially your signal model is cos(2*pi*B*t^2) This means that when you look a...

7 years ago | 0

| accepted

Answered
How can I add a shifted version of a signal to the original signal?
Can you clarify why the result of delayseq() does not satisfy your needs? Thanks.

8 years ago | 0

Answered
Projection between two coordinate systems
Let's use coodinate system g as the reference and assume your coordinates are Pg = [xg;yg;zg]. For coordinate system l, the orgi...

8 years ago | 0

Answered
How can i draw contours of a function of the form f(x)=X1^2+X2^2?
Are you looking for something like this? ezcontour(@(x1,x2)x1.^2+x2.^2) HTH

8 years ago | 0

Answered
Insert values of a vector between two elements of another vector and at the end of it.
Is it just c = [a;b] c = c(:) Did I understand it correctly? HTH

8 years ago | 1

| accepted

Answered
How to match two matrices
Are you trying to align the two signals so [800 798] in column 1 matches [800 798] in columns 2? In that case you can try |align...

8 years ago | 0

| accepted

Answered
fdesign 'rational sample rate converter' rsrc sampling frequency
I believe it's the sampling rate of the input signal to the filter, so in your case, I think it's the interpolated sampling rate...

8 years ago | 0

Answered
multi user beamforming using lte toolbox
Have you seen the following example, maybe it can serve as a starting point. <https://www.mathworks.com/help/phased/examples/...

8 years ago | 0

Answered
Radar and signal processing.
You may want to take a look at |ambgfun| function from Phased Array System Toolbox <https://www.mathworks.com/help/phased/ref...

8 years ago | 0

Answered
phased.CustomAntennaElement Import and Interpolate
We currently don't support this yet but this is something we want to support in the product. There are many different ways to do...

8 years ago | 0

| accepted

Answered
about 'phased.FreeSpace' function.
You can use the |fspl| function to compute the loss and compensate accordingly, but do you mind sharing your use case? I'm curio...

8 years ago | 1

Answered
pwelch vs fft, plotting with 10*log10
1. pwelch uses Welch method, which involves windowing and averaging on top of fft, that's why they are different. The basic shap...

8 years ago | 2

Answered
making UCA using spirall antenna
If you have 17 frequencies, then your FrequencyResponse is either a scalar, which means the response is flat across all frequenc...

8 years ago | 0

Answered
When I compute the cross spectral densitiy function Pxy using cpsd.m, and divide by Pxx, the angle is the wrong sign when compared to tfestimate.m Why is that.
This is because in |tfestimate|, the transfer function is defined as Pyx/Pxx, and Pyx is conjugate of Pxy, that's why you see th...

8 years ago | 0

Answered
making UCA using spirall antenna
Phased Array System Toolbox models antenna at pattern level. You have two choices: 1. Capture the pattern of a spiral antenna...

8 years ago | 0

Answered
What stage to add noise in FMCW radar system?
The line sig2=receiver(sig) already adds noise to the signal and the noise power is determined by the parameters in rece...

8 years ago | 0

Answered
Can anyone help me how to open this file ? The file is genererated by a pulse radar.....
This looks like a binary file format. It's not clear to me whether you want to read or write such a file but MATLAB provides the...

8 years ago | 0