deconvlucy function to deblur an
image using the accelerated, damped, Lucy-Richardson algorithm. The algorithm
maximizes the likelihood that the resulting image, when convolved with the PSF, is
an instance of the blurred image, assuming Poisson noise statistics. This function
can be effective when you know the PSF but know little about the additive noise in
deconvlucy function implements several adaptations to the
original Lucy-Richardson maximum likelihood algorithm that address complex image
Noise amplification is a common problem of maximum likelihood methods that attempt to fit data as closely as possible. After many iterations, the restored image can have a speckled appearance, especially for a smooth object observed at low signal-to-noise ratios. These speckles do not represent any real structure in the image, but are artifacts of fitting the noise in the image too closely.
To control noise amplification, the
deconvlucy function uses a
DAMPAR. This parameter specifies the threshold
level for the deviation of the resulting image from the original image, below which
damping occurs. For pixels that deviate in the vicinity of their original values,
iterations are suppressed.
Damping is also used to reduce ringing, the appearance of high-frequency structures in a restored image. Ringing is not necessarily the result of noise amplification. See Avoid Ringing in Deblurred Images for more information.
Another complication of real-life image restoration is that the data might include
bad pixels, or that the quality of the receiving pixels might vary with time and
position. By specifying the
WEIGHT array parameter with the
deconvlucy function, you can specify that certain pixels in
the image be ignored. To ignore a pixel, assign a weight of zero to the element in
WEIGHT array that corresponds to the pixel in the
The algorithm converges on predicted values for the bad pixels based on the
information from neighborhood pixels. The variation in the detector response from
pixel to pixel (the so-called flat-field correction) can also be accommodated by the
WEIGHT array. Instead of assigning a weight of 1.0 to the
good pixels, you can specify fractional values and weight the pixels according to
the amount of the flat-field correction.
Noise in charge coupled device (CCD) detectors has two primary components:
Photon counting noise with a Poisson distribution
Read-out noise with a Gaussian distribution
The Lucy-Richardson iterations intrinsically account for the first type of noise. You must account for the second type of noise; otherwise, it can cause pixels with low levels of incident photons to have negative values.
deconvlucy function uses the
input parameter to handle camera read-out noise. The value of this parameter is
typically the sum of the read-out noise variance and the background noise (e.g.,
number of counts from the background radiation). The value of the
READOUT parameter specifies an offset that ensures that all
values are positive.
The restoration of undersampled data can be improved significantly if it is done
on a finer grid. The
deconvlucy function uses the
SUBSMPL parameter to specify the subsampling rate, if the PSF
is known to have a higher resolution.
If the undersampled data is the result of camera pixel binning during image acquisition, the PSF observed at each pixel rate can serve as a finer grid PSF. Otherwise, the PSF can be obtained via observations taken at subpixel offsets or via optical modeling techniques. This method is especially effective for images of stars (high signal-to-noise ratio), because the stars are effectively forced to be in the center of a pixel. If a star is centered between pixels, it is restored as a combination of the neighboring pixels. A finer grid redirects the consequent spreading of the star flux back to the center of the star's image.
deconvlucyFunction to Deblur an Image
To illustrate a simple use of
deconvlucy, this example
simulates a blurred, noisy image by convolving a Gaussian filter PSF with an image
imfilter) and then adding Gaussian noise of variance
V to the blurred image (using
Read an image into the MATLAB® workspace. (The example uses cropping to reduce the size of the image to be deblurred. This is not a required step in deblurring operations.)
I = imread('board.tif'); I = I(50+[1:256],2+[1:256],:); figure, imshow(I) title('Original Image')
Create the PSF.
PSF = fspecial('gaussian',5,5);
Create a simulated blur in the image and add noise.
Blurred = imfilter(I,PSF,'symmetric','conv'); V = .002; BlurredNoisy = imnoise(Blurred,'gaussian',0,V); figure, imshow(BlurredNoisy) title('Blurred and Noisy Image')
deconvlucy to restore the
blurred and noisy image, specifying the PSF used to create the blur, and
limiting the number of iterations to 5 (the default is 10).
deconvlucy function can return values in the
output image that are beyond the range of the input image.
luc1 = deconvlucy(BlurredNoisy,PSF,5); figure, imshow(luc1) title('Restored Image')
deconvlucy function, by default, performs multiple
iterations of the deblurring process. You can stop the processing after a certain
number of iterations to check the result, and then restart the iterations from the
point where processing stopped. To do this, pass in the input image as a cell array,
function returns the output image as a cell array that you can then pass as an input
deconvlucy to restart the deconvolution.
The output cell array contains these four elements:
Original input image
Image produced by the last iteration
Image produced by the next to last iteration
Internal information used by
deconvlucy function supports several other optional
arguments you can use to achieve the best possible result, such as specifying a
damping parameter to handle additive noise in the blurred image. To see the impact
of these optional arguments, see the example Deblurring Images Using the Lucy-Richardson Algorithm.