Blockset™ product supports an interface to the third-party FlightGear flight
simulator, open-source software available through a GNU General Public License
(GPL). The FlightGear flight simulator interface included with the blockset is a
unidirectional transmission link from the Simulink® interface to FlightGear using the FlightGear published
net_fdm binary data exchange protocol. Data is transmitted
via UDP network packets to a running instance of FlightGear. The blockset supports
multiple standard binary distributions of FlightGear. See Run FlightGear with Simulink Models for interface details.
FlightGear is a separate software entity not created, owned, or maintained by MathWorks.
The Aerospace Blockset product supports these FlightGear versions:
If you are using a FlightGear version older than 2.0, update your FlightGear installation to a
supported version. When you open the model, the software returns a warning or error.
Obtain updated FlightGear software from
https://www.flightgear.org in the download
You can obtain FlightGear from the FlightGear website in the download area or by ordering CDs from FlightGear. The download area contains extensive documentation for installation and configuration. Because FlightGear is an open-source project, source downloads are also available for customizing and porting to custom environments.
To use FlightGear, you must have a high-performance graphics card with stable drivers For more information, see the FlightGear CD distribution or the hardware requirements and documentation areas of the FlightGear website.
FlightGear performance and stability can be sensitive to computer video cards, driver versions, and driver settings. You need OpenGL® support with hardware acceleration activated. Without proper setup, performance can drop from about a 30 frames-per-second (fps) update rate to less than 1 fps. If your system allows you to update OpenGL settings, modify them to improve performance.
For Windows® systems, use the following graphics recommendations:
A graphics card with acceptable OpenGL performance (as outlined at the FlightGear website).
The latest tested and stable driver release for your video card. Test the driver thoroughly on a few computers before deploying to others.
For more information, see
FlightGear distributions are available for Linux®, Macintosh, and other platforms from the FlightGear website,
https://www.flightgear.org. Installation on
these platforms, like Windows, requires careful configuration of graphics cards
and drivers. Consult the documentation and hardware requirements sections at the
Your computer built-in video card, such as NVIDIA® cards, can conflict with FlightGear shaders. Consider this workaround:
Disable the FlightGear shaders by selecting the Generate Run Script block Disable FlightGear shader options check box.
The extensive FlightGear documentation guides you through the installation in detail. Consult the following:
Documentation section of the FlightGear website for installation
MATLAB® system requirements.
Keep the following points in mind:
Configure your computer graphics card before you install FlightGear. See the preceding section, Configure Your Computer for FlightGear.
Shut down all running applications (including the MATLAB interface) before installing FlightGear.
Install FlightGear in a folder path name composed of ASCII characters.
MathWorks tests indicate that the operational stability of FlightGear is especially sensitive during startup. It is best not to move, resize, mouse over, overlap, or cover up the FlightGear window until the initial simulation scene appears after the startup splash screen fades out.
Aerospace Blockset supports FlightGear on several platforms. This table lists the properties to consider before you start to use FlightGear.
|FlightGear Property||Folder Description||Platforms||Typical Location|
|FlightGear installation folder.||Windows 64-bit|
|Linux||Folder into which you installed FlightGear|
(folder to which you dragged the FlightGear icon)
|Model geometry folder||Windows 64-bit|
When you install the FlightGear software, the installation provides a basic level of scenery files. The FlightGear documentation guides you through installing scenery as part the general FlightGear installation.
If you need to install more FlightGear scenery files, see the instructions at
instructions describe how to install the additional scenery in a default location.
MathWorks® recommends that you follow those instructions.
If you install additional scenery in a nonstandard location, you may need to update the
FG_SCENERY environment variable in the script output from the
Generate Run Script block to include
the new path. For a description of the
FG_SCENERY variable, see
the documentation at https://www.flightgear.org.
If you do not download scenery in advance, you can direct FlightGear to download it automatically during simulation by selecting the Generate Run Script block Install FlightGear scenery during simulation (requires Internet connection) check box.
For Windows systems, you may encounter an error message while launching FlightGear
InstallScenery option enabled:
Error creating directory: No such file or directory
This error likely indicates that your default FlightGear download folder is not
writeable, the path cannot be resolved, or the path contains UNC path names. To work
around the issue, edit the
runfg.bat file to specify a new folder
path to store the scenery data:
To the list of command options, append
and specify a folder to which to download the scenery data. For
All data downloaded during this FlightGear session is saved to the specified directory. To avoid downloading duplicate scenery data, use the same directory in succeeding FlightGear sessions
To open FlightGear, run
Each time that you run the Generate Run Script block, it creates a new script. It overwrites any edits that you have added.