Troubleshooting SPI Interface
Serial Peripheral Interface (SPI) is a synchronous serial data link standard that operates in full duplex mode. It is commonly used in the test and measurement field. Common uses include communicating with micro controllers, EEPROMs, A2D devices, embedded controllers, etc.
Instrument Control Toolbox™ SPI support lets you open connections with individual chips and to read
and write over the connections to individual chips using an Aardvark or NI-845x host
adapter. The primary uses for the
spi interface involve the
writeAndRead functions for synchronously reading and writing
You need to have either a Total Phase Aardvark host adapter or an NI-845x adapter
board installed to use the
The SPI interface is supported on these platforms when used with the Aardvark host adapter:
Linux® — Red Hat® Enterprise Linux 4 and 5 with kernel 2.6, and possibly SUSE® and Ubuntu distributions.
Microsoft® Windows® 64-bit
For R2018b and R2018a, you cannot use the Aardvark adapter for I2C or SPI interfaces on the macOS platform. You can still use it on Windows and Linux. For releases prior to R2018a, you can use it on all three platforms, including macOS.
The SPI interface is supported on these platforms when used with the NI-845x host adapter:
Microsoft Windows 64-bit
You need either a Total Phase Aardvark host adapter or an NI-845x adapter board
installed to use the
spi interface. The following sections
describe requirements for each option.
To use the SPI interface with the Aardvark adapter, make sure you install the following software.
Uninstall any existing Aardvark Software API on your computer. Download and install the Instrument Control Toolbox Support Package for Total Phase™ Aardvark I2C/SPI™ Interface. For more information, see Install the Total Phase Aardvark I2C/SPI Interface Support Package.
Make sure that the Aardvark adapter is connected to your computer using the USB connector.
Optionally, you can also check that the Aardvark adapter is working properly in the Total Phase Control Center Serial Software.
To use the SPI interface with the NI-845x adapter, download the hardware support package to obtain the latest driver, if you do not already have the driver installed. If you already have the latest driver installed, you do not need to download this support package.
If you do not have the NI-845x driver installed, see Install the NI-845x I2C/SPI Interface Support Package to install it.
Configuration and Connection
Make sure that you have the correct instrument driver installed for your device. Refer to your device’s documentation and the vendor’s web site.
Make sure your device is supported in Instrument Control Toolbox. See Is My Hardware Supported?.
You must have a Total Phase Aardvark host adapter or an NI-845x adapter board installed to use the SPI interface. Install the appropriate support package if you have not already. See Adapter Requirements.
Make sure that your SPI adapter board is plugged into the computer running MATLAB®. You can verify that you have one of the adapters installed by using the
instrhwinfofunction with the
If you do not see either
ni845xlisted, you need to install one of the support packages or install the driver directly from the vendor.
Make sure that Instrument Control Toolbox recognizes your device, by using the
instrhwinfofunction with the
spiinterface name, and your adapter name, either
ni845x. For example:
You will need the information displayed to create the
spiobject. If your device is not displayed, check the previous steps.
Make sure you can create the
spiobject. You must provide three arguments to create the object.
Portare both usually
'ni845x'. This example uses a SPI object called
Sthat communicates to an EEPROM chip. Create the object using the
Portnumbers, which are
0in both cases.
% Vendor = aardvark % BoardIndex = 0 % Port = 0 S = spi('aardvark', 0, 0);
If you do not get an error, the object was created successfully. To verify, you can look at the object properties, using the name you assigned to the object,
Sin this case.
Make sure you can connect to the device, using the
connectfunction with the object name.
If you do not get an error, the connection was made successfully. If you do get an error, follow the steps in the error message and/or check the previous steps listed here.
When you have connected, you can communicate with your device. See Transmitting Data Over the SPI Interface for an example of reading and writing to a chip.