device

Connection to serial device on Arduino or ESP32 hardware

Add-On Required: This feature requires the MATLAB Support Package for Arduino Hardware add-on.

Description

This object represents a connection to the serial device connected to Arduino^® or ESP32 hardware. You can interact with the serial device using the functions listed in Object Functions.

Creation

Syntax

serialdevObj = device(arduinoObj,'SerialPort',SerialPort)

serialdevObj = device(arduinoObj,'SerialPort',SerialPort,Name,Value)

Description

serialdevObj = device(arduinoObj,'SerialPort',SerialPort) creates an object that represents the connection between the serial device connected to the Arduino or ESP32 hardware at the serial port specified by SerialPort. The Arduino hardware is represented by an arduino object.

serialdevObj = device(arduinoObj,'SerialPort',SerialPort,Name,Value) creates an object that represents the connection with additional options specified by one or more Name,Value pair arguments between the serial device connected to the Arduino or ESP32 hardware.

Input Arguments

SerialPort — Serial port ID

numeric

The ID of the serial port available on the Arduino or ESP32 hardware specified as a number.

Example: serialdevObj = device(arduinoObj,'SerialPort',1)

Note

The Arduino Mega2560, Due, and MegaADK boards have three serial ports available while the Arduino Leonardo, Micro, MKR1000, MKR1010, MKRZero, Nano33IoT, and Nano33BLE have one serial port available.

Note

For ESP32 modules, the supported SerialPort value is 2.

arduinoObj — Arduino or ESP32 hardware connection

arduino object

Arduino or ESP32 hardware connection, specified as an arduino object.

Name-Value Arguments

Specify optional pairs of arguments as Name1=Value1,...,NameN=ValueN, where Name is the argument name and Value is the corresponding value. Name-value arguments must appear after other arguments, but the order of the pairs does not matter.

Before R2021a, use commas to separate each name and value, and enclose Name in quotes.

Example: serialdevObj = device(arduinoObj,'SerialPort',1,'BaudRate',115200);

BaudRate — Bit transmit rate

9600 (default) | 300 | 600 | 1200 | 2400 | 4800 | 14400 | 19200 | 28800 | 38400 | 57600 | 115200

The rate at which bits are transmitted in bits/s specified as a number.

Example: serialdevObj = device(arduinoObj,'SerialPort',1,'BaudRate',115200);

Note

If you are using more than one device, make sure the devices operate at same BaudRate for data consistency.

DataBits — Number of data bits to transmit

8 (default) | 5 | 6 | 7

Number of data bits to transmit, specified as a number.

Example: serialdevObj = device(arduinoObj,'SerialPort',1,'BaudRate',115200, 'DataBits',8);

StopBits — Number of bits to indicate end of byte

1 (default) | 2

Number of bits to indicate the end of data transmission, specified as a number.

Example: serialdevObj = device(arduinoObj,'SerialPort',1,'BaudRate',115200, 'DataBits',8, 'StopBits',1);

Data Types: double

Parity — Type of parity check

none (default) | odd | even

Parity for the serial communication specified as a character vector.

Example: serialdevObj = device(arduinoObj,'SerialPort',1,'BaudRate',115200, 'DataBits',8, 'StopBits',1, 'Parity','even');

Timeout — Maximum time to wait for serial data

1 (default) | [0 8]

Maximum time in seconds to wait for serial data, specified as a number.

Example: serialdevObj = device(arduinoObj,'SerialPort',1,'BaudRate',115200, 'DataBits',8, 'StopBits',1, 'Parity','even','Timeout',2);

Properties

Interface — Type of interface used for communication

'Serial'

This property is read-only.

Type of interface used for communication.

Example:

>> serialdevObj.Interface
ans = 
      Serial

SerialPort — Serial port ID

numeric

Serial port available on the Arduino or ESP32 hardware, specified as a number.

Example:

>> serialdevObj.SerialPort
ans = 
      1 

Data Types: double

TxPin — Transmission pin

character vector

Transmission pin for serial communication.

Example:

>> serialdevObj.TxPin
ans = 
      'D18' 

Data Types: char

RxPin — Receive pin

character vector

Receive pin for serial communication.

Example:

>> serialdevObj.RxPin
ans = 
      'D19' 

Data Types: char

BaudRate — Bit transmit rate

9600 (default) | 300 | 600 | 1200 | 2400 | 4800 | 14400 | 19200 | 28800 | 38400 | 57600 | 115200

The rate at which bits are transmitted in bits/s specified as a number.

Example:

>> serialdevObj.BaudRate
ans = 
      115200

Data Types: double

NumBytesAvailable — Number of bytes to read

numeric

This property is read-only.

Number of bytes of data available to read from the serial device, specified as a number.

Example:

>> serialdevObj.NumBytesAvailable
ans = 
      0 

Data Types: double

Parity — Type of parity check

none (default) | odd | even

Parity for the serial communication specified as a character vector.

Example:

>> serialdevObj.Parity
ans = 
      'even' 

Data Types: char

StopBits — Number of bits to indicate end of byte

1 (default) | 2

Number of bits to indicate the end of data transmission, specified as a number.

Example:

>> serialdevObj.StopBits

ans =
     1

Data Types: double

DataBits — Number of data bits to transmit

8 (default) | 5 | 6 | 7

Number of data bits to transmit, specified as a number.

Example:

>> serialdevObj.DataBits

ans =
     8 

Data Types: double

Timeout — Maximum time to wait for serial data

1 (default) | [0 8]

Maximum time in seconds to wait for serial data, specified as a number.

Example:

>> serialdevObj.Timeout

ans =
     1

Data Types: double

Object Functions

read	Read data from serial device
write	Write data to serial device

Examples

Create Connection to Serial Device on Arduino Hardware

Create an arduino connection.

arduinoObj = arduino("COM16","Leonardo","Libraries",{'SPI','Serial','I2C'})

arduinoObj = 
  arduino with properties:

                  Port: 'COM16'
                 Board: 'Leonardo'
         AvailablePins: {'D2-D13', 'A0-A5'}
  AvailableDigitalPins: {'D2-D13', 'A0-A5'}
      AvailablePWMPins: {'D3', 'D5-D6', 'D9-D11', 'D13'}
   AvailableAnalogPins: {'A0-A5', 'D4', 'D6', 'D8-D10', 'D12'}
    AvailableI2CBusIDs: [0]
AvailableSerialPortIDs: [1]
             Libraries: {'I2C', 'SPI', 'Serial'}

Create a connection to the serial device on the Arduino hardware.

serialdevObj = device(arduinoObj,'SerialPort',1)

serialdevObj = 
  device with properties:

             Interface: 'Serial'
            SerialPort: 1
                 TxPin: 'D1'
                 RxPin: 'D0'
              BaudRate: 9600 (bits/s) 
     NumBytesAvailable: 0 

Show all properties, functions

Specify Baud Rate of Serial Device

Create an arduino connection.

arduinoObj = arduino("COM16","Leonardo","Libraries",{'SPI','Serial','I2C'})

arduinoObj = 
  arduino with properties:

                  Port: 'COM16'
                 Board: 'Leonardo'
         AvailablePins: {'D2-D13', 'A0-A5'}
  AvailableDigitalPins: {'D2-D13', 'A0-A5'}
      AvailablePWMPins: {'D3', 'D5-D6', 'D9-D11', 'D13'}
   AvailableAnalogPins: {'A0-A5', 'D4', 'D6', 'D8-D10', 'D12'}
    AvailableI2CBusIDs: [0]
AvailableSerialPortIDs: [1]
             Libraries: {'I2C', 'SPI', 'Serial'}

Create a connection to the serial device with the BaudRate set to 115200 bits/s.

serialdevObj = device(arduinoObj,'SerialPort',1,'BaudRate', 115200)

serialdevObj = 
  device with properties:

             Interface: 'Serial'
            SerialPort: 1
                 TxPin: 'D1'
                 RxPin: 'D0'
              BaudRate: 115200 (bits/s) 
     NumBytesAvailable: 0 

Show all properties, functions

More About

Code Generation Using MATLAB Function Block

• Use device in a MATLAB^® Function block with the Simulink^® Support Package for Arduino Hardware to generate code that can be deployed on Arduino or ESP32 Hardware.

• Specifying BaudRate as a name value pair argument is not supported the in MATLAB Function block. You can set BaudRate from the Configuration Parameters dialog box. To set the BaudRate:

  • On the Simulink Toolstrip, in the Hardware tab, click Hardware Settings to open the Configuration Parameters dialog box.

  • In the Configuration Parameters dialog box, select Hardware Implementation. Verify that the Hardware board parameter is set to the appropriate Arduino board.

  • Go to Hardware board settings > Target hardware resources > Serial port properties.

  • Enter the value to set BaudRate in the particular serial port.

• Default value of Timeout is 0.

• The property DataBits cannot be changed and always uses a default value 8.

• The property Parity cannot be changed and always uses a default valuenone.

• The property StopBit cannot be changed and always uses a default value1.

• The properties Interface, BitRate, SCLPin, and SDAPin are not accessible from the device object.

Version History

Introduced in R2019b