Clear Filters
Clear Filters

how to velocize execution code

12 views (last 30 days)
Luca Re
Luca Re on 30 Aug 2024
Edited: Luca Re on 21 Oct 2024 at 14:22
load('matlab_v1.mat')
load('matlab_v2.mat')
[r,c]=size(v1);
res=zeros(size(v1));
t=0;
for i=1:c
for ii=1:r
a=v1(ii,i);
b=v2(ii,i);
if a
t=0;
end
if b
t=1;
end
Res(ii,i)=t;
end
end
%explanation:
%When v1=1 then i set=0 Res until the end
%When v2=1 then i set=1 Res until the end
it's possibile to velocize it avoid loop (using vectorizing or other)
  2 Comments
Walter Roberson
Walter Roberson on 30 Aug 2024
if a
t=0;
end
if b
t=1;
end
It is possible that a is 0 and b is also 0. In that case, t will remain unchanged. That makes it more difficult to vectorize, since you have to copy the previous t .
Luca Re
Luca Re on 30 Aug 2024
yes..that's correct

Sign in to comment.

Accepted Answer

Walter Roberson
Walter Roberson on 30 Aug 2024
load('matlab_v1.mat')
load('matlab_v2.mat')
res = nan(size(v1));
res(v1 ~= 0) = 0;
res(v2 ~= 0) = 1;
res = reshape(fillmissing( res(:), 'previous', 'EndValues', 0), size(res));
  2 Comments
Luca Re
Luca Re on 30 Aug 2024
thank..very good...is more speed
Luca Re
Luca Re on 20 Oct 2024 at 20:55
Edited: Luca Re on 21 Oct 2024 at 14:22
using this data your code is not correct
your solution is not equal to this my code
[r,c]=dimensione(v1);
res=zeros(dimensione(v1));
t=0;
per i=1:c
per ii=1:r
a=v1(ii,i);
b=v2(ii,i);
se un
t=0;
FINE
se b
t=1;
FINE
Res(ii,i)=t;
FINE
FINE

Sign in to comment.

More Answers (1)

Jatin
Jatin on 30 Aug 2024
Hi Luca,
As per my understanding, you are trying to fill a new logical array “res” which is assigned a value of 0 if the logical array v1 has a value 1 and assigned a value 1 if the logical array v2 has a value 1.
The above requirement can be easily vectorized in MATLAB using logical indexing of arrays. Refer the script below:
res = zeros(size(v1));
% Logical indexing to set values based on conditions
res(v2) = 1; % Set to 1 where v2 is true
The assignment of res using v1 is not necessary because res is already initialized to all zero so assignment of “0” is redundant here.
Note: If you are trying to assign the values of res as a switch where you keep on assigning a value 1 until you encounter v1 = 1” and assign value 0 until you encounter v2 = 1”. In this case the current assignment results depend on the previous state and hence vectorized assignment cannot be done.
You can refer the documentation below for information on “Array Indexing on logical values”:
  9 Comments
Jatin
Jatin on 30 Aug 2024
"why uppercase is more slow of lowercase?"
Stephen23 pointed out that using "res" instead of "Res" can enhance speed because "res" is already pre-initialized in your code. Since "Res" was not pre-initialized, every time you assign values to it, memory has to be dynamically allocated, which adds overhead. By pre-initializing "res," you avoid this overhead, saving time in your operations.

Sign in to comment.

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!