Do Simulink "Deploy to Hardware" and "External" modes work with Arduino Uno clones?
241 views (last 30 days)
Multiplexer on 8 Aug 2017
There are two popular clones of original Arduino Uno:
- old clones that use CH340 chip for USB to Serial communication with PC and programming (requires 3rd party Serial to USB driver)
- new clones that use ATmega16u2 for USB to SErial communication with PC and programming (claims to use original Arduino drivers)
My question is, does anybody know, have anybody tried running Arduino Uno clones with Simulink External/Deploy mode? If yes did it work? Which board exactly were you using (new clone with ATmega16u2 or old with CH340)?
I'm asking this question because I'm planning practical demonstration on how to program Arduino with Simulink and unfortunately I can't enforce that every single participant will have original Arduino and I'm trying to find out how severe problem it can be if one tries to use clone.
Sudeshna Bhattacharya on 7 Nov 2017
Edited: Sudeshna Bhattacharya on 7 Nov 2017
The "Deploy to Hardware" should work fine with both CH340 and ATmega16u2 clones. For most of the Arduino boards the External mode baud rate is set to 921600. I have observed that CH340 cannot handle baudrate greater than 230400. This is the reason that External mode fails.
There is a hidden API to change the default External mode baudrate. Open the model. Check the default External mode baudrate by executing the below command:
If you want to change the baudrate to a lower value say 230400 then use: >>codertarget.arduinobase.registry.setBaudRate(gcs,230400)
If you have an issue with External mode even after setting External mode baudrate to 230400 then keep lowering it till External mode works.
Ideally the clones with ATmega16u2 that use original Arduino drivers should work seamlessly in External mode. I have not yet tested though.
More Answers (10)
Erneto Rosas on 12 Mar 2019
Hello every one, i just fixed the problem, first i noticed that i just received the error message in the external mode because in normal mode that worked well, what you have to do when you are using a USB-SERIAL CH340 is to change the BaudRate by using the command codertarget.arduinobase.registry.setBaudRate(gcr,*nomberofBaudRate)
the Baud rates choices are 76800, 115200,128000, 153600, 230400, 460800, 921600, 1500000, 2000000.
mine worked using the 153660
Javier Pérez de Arrilucea Santiró on 6 Jan 2021
I am running Matlab 2020a and I cannot even select the external mode in the drop-down menu (not appearing).
My clone is using the ATmega.
Kwadwo Dompreh on 2 Nov 2017
yes, Arduino mega2560 (clone from china) works fine in external mode for R2015a but does not work in external mode for R2017a (In normal only).
Jingbo on 3 Nov 2017
I tried to run simulink block in arduino board (CH340 driver) with external mode,it always shown some errors. Finally, I change another arduino board (with original driver), everything is good , external mode run on simulink went well. IF you want to buy cheap arduino board for simulink external mode and display and tune real-time.we recommend you buy farduino from Amazon that is cheaper than original arduino board.
David Sandells on 5 Aug 2018
I found that a baud rates of 115200 and 128000 worked for my Elegoo Nano board (uses CH340 driver). It wouldn't take the next 'standard' rate of 256000. Not sure if some other intermediate values might work.
FYI - I had previously tried changing the startDaemon file to the .m file version as suggested in the "Why am I unable to connect to Arduino in External Mode?" post. I didn't play with the delay value suggested in that post as it was already set to 180 seconds in the file provided. Anyway that solution on its own didn't have any affect but I guess it could have helped in combination with the baud rate change I mentioned above (which is why I mention it here).
Pablo Angulo on 6 Apr 2019
In Conclusion, I could work in external mode, with my Arduino MEGA 2650 Made in China whith CH340 controller in Matlab R2017b, in effect we must to change Boud Rate, in may case worked using 153660 as well, the example code is:
For the follow example you must to have opened your Simulink Project, after that:
In Worspace windows :
For checking Boud Rate you can wrinte im promp
After that you can try to play your Clone Arduino Made in China in External Mode.
Thanks a lot
Anshuman Deshpande on 13 May 2019
In my case for Arduino Uno, it worked with--> codertarget.arduinobase.registry.setBaudRate(gcs,153660)
Md Ohirul Qays on 13 Sep 2019
Matlab 2018b interfaced with Arduino 2560 performed the command line successfully.
Nextly, the another baud rate 9600 is followed properly as well.
Angel Casas on 4 Dec 2019
Gracias a todos por sus comentarios. Tengo un Arduino NANO (clon) y me funcionó con 230400 baudios.