How do I pass the signal to the frequency domain?

Hello to everyone. I have one noisy signal, and this signal is in the time domain. I want to draw this signal through the Fourier transform. As a result, what I expect is a Gaussian dispersion around 0. However, I don't know how to apply and draw the Fourier transform on my signal. I would be glad if you could help.

signalplusnoise=1x674

signalplusnoise=[0.0161,0.0308, 0.0112, ..., 0.3827]

Answer 1

[Mathieu NOE]

hello

see below a code to do spectral analysis (example)

but to me you're confusing fft with histogram. The fft spectrum will give you the amplitudes of the noise frequencies and they all will be positive and spread across the frequency range from zero to Fs/2.

[studentmatlaber]

Thank you very much for the example, but it seemed confused for me as I am more inexperienced. First, I was asked to convert the signal to frequency environment and draw it, then I will pass through the low pass filter.

[Mathieu NOE]

ok , do you have started something ? have a code ?

can you share your data ?

tx

[studentmatlaber]

In the signalcode file, each line of the signal cell contains a signal. I want to plot the signal in each line in frequency medium. I couldn't start a code about this, but the data I have is like this. Thank you very much for your time.

[Mathieu NOE]

hello

so I understood all "y" data share thesame time axis (vector, so one is sufficient for my code

I show you how I merged four of the y vector into one matrix to compute and display time / averaged fft and spectrogram

your signals does not contain a lot of "dynamic" stuff so the energy of the fft (and spectrogram) is located at very very low frequency

clc
clearvars
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% load signal
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

%% data
load('Data_x30_y30_28.mat');
signal = [y1(:) y2(:) y3(:) y4(:)];  % concatenate more "y" vectors (column oriented) if needed

t = t1;
dt = mean(diff(t));
Fs = 1/dt;

[samples,channels] = size(signal);

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% FFT parameters
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
NFFT = 128;    % 
OVERLAP = 0.95;

% spectrogram dB scale
spectrogram_dB_scale = 80;  % dB range scale (means , the lowest displayed level is XX dB below the max level)

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% options 
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% if you are dealing with acoustics, you may wish to have A weighted
% spectrums 

% option_w = 0 : linear spectrum (no weighting dB (L) )
% option_w = 1 : A weighted spectrum (dB (A) )
option_w = 0;

%% decimate (if needed)
% NB : decim = 1 will do nothing (output = input)
decim = 1;
if decim>1
    for ck = 1:channels
    newsignal(:,ck) = decimate(signal(:,ck),decim);
    Fs = Fs/decim;
    end
   signal = newsignal;
end
samples = length(signal);
time = (0:samples-1)*1/Fs;

%%%%%% legend structure %%%%%%%%
for ck = 1:channels
    leg_str{ck} = ['Channel ' num2str(ck) ];
end
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% display 1 : time domain plot
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
figure(1),plot(time,signal);grid on
title(['Time plot  / Fs = ' num2str(Fs) ' Hz ']);
xlabel('Time (s)');ylabel('Amplitude');
legend(leg_str);

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% display 2 : averaged FFT spectrum
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

[freq, sensor_spectrum] = myfft_peak(signal,Fs,NFFT,OVERLAP);

% convert to dB scale (ref = 1)
sensor_spectrum_dB = 20*log10(sensor_spectrum);

% apply A weigthing if needed
if option_w == 1
    pondA_dB = pondA_function(freq);
    sensor_spectrum_dB = sensor_spectrum_dB+pondA_dB;
    my_ylabel = ('Amplitude (dB (A))');
else
    my_ylabel = ('Amplitude (dB (L))');
end


figure(2),plot(freq,sensor_spectrum_dB);grid on
df = freq(2)-freq(1); % frequency resolution 
title(['Averaged FFT Spectrum  / Fs = ' num2str(Fs) ' Hz / Delta f = ' num2str(df,3) ' Hz ']);
xlabel('Frequency (Hz)');ylabel(my_ylabel);
legend(leg_str);

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% display 3 : time / frequency analysis : spectrogram demo
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
for ck = 1:channels
    [sg,fsg,tsg] = specgram(signal(:,ck),NFFT,Fs,hanning(NFFT),floor(NFFT*OVERLAP));  

    % FFT normalisation and conversion amplitude from linear to dB (peak)
    sg_dBpeak = 20*log10(abs(sg))+20*log10(2/length(fsg));     % NB : X=fft(x.*hanning(N))*4/N; % hanning only

    % apply A weigthing if needed
    if option_w == 1
        pondA_dB = pondA_function(fsg);
        sg_dBpeak = sg_dBpeak+(pondA_dB*ones(1,size(sg_dBpeak,2)));
        my_title = ('Spectrogram (dB (A))');
    else
        my_title = ('Spectrogram (dB (L))');
    end

    % saturation of the dB range : 
    % saturation_dB = 60;  % dB range scale (means , the lowest displayed level is XX dB below the max level)
    min_disp_dB = round(max(max(sg_dBpeak))) - spectrogram_dB_scale;
    sg_dBpeak(sg_dBpeak<min_disp_dB) = min_disp_dB;

    % plots spectrogram
    figure(2+ck);
    imagesc(tsg,fsg,sg_dBpeak);colormap('jet');
    axis('xy');colorbar('vert');grid on
    df = fsg(2)-fsg(1); % freq resolution 
    title([my_title ' / Fs = ' num2str(Fs) ' Hz / Delta f = ' num2str(df,3) ' Hz / Channel : ' num2str(ck)]);
    xlabel('Time (s)');ylabel('Frequency (Hz)');

end

function pondA_dB = pondA_function(f)
	% dB (A) weighting curve
	n = ((12200^2*f.^4)./((f.^2+20.6^2).*(f.^2+12200^2).*sqrt(f.^2+107.7^2).*sqrt(f.^2+737.9^2)));
	r = ((12200^2*1000.^4)./((1000.^2+20.6^2).*(1000.^2+12200^2).*sqrt(1000.^2+107.7^2).*sqrt(1000.^2+737.9^2))) * ones(size(f));
	pondA = n./r;
	pondA_dB = 20*log10(pondA(:));
end


function  [freq_vector,fft_spectrum] = myfft_peak(signal, Fs, nfft, Overlap)
% FFT peak spectrum of signal  (example sinus amplitude 1   = 0 dB after fft).
% Linear averaging
%   signal - input signal, 
%   Fs - Sampling frequency (Hz).
%   nfft - FFT window size
%   Overlap - buffer percentage of overlap % (between 0 and 0.95)

[samples,channels] = size(signal);

% fill signal with zeros if its length is lower than nfft
if samples<nfft
    s_tmp = zeros(nfft,channels);
    s_tmp((1:samples),:) = signal;
    signal = s_tmp;
    samples = nfft;
end

% window : hanning
window = hanning(nfft);
window = window(:);

%    compute fft with overlap 
 offset = fix((1-Overlap)*nfft);
 spectnum = 1+ fix((samples-nfft)/offset); % Number of windows
%     % for info is equivalent to : 
%     noverlap = Overlap*nfft;
%     spectnum = fix((samples-noverlap)/(nfft-noverlap));	% Number of windows

    % main loop
    fft_spectrum = 0;
    for i=1:spectnum
        start = (i-1)*offset;
        sw = signal((1+start):(start+nfft),:).*(window*ones(1,channels));
        fft_spectrum = fft_spectrum + (abs(fft(sw))*4/nfft);     % X=fft(x.*hanning(N))*4/N; % hanning only 
    end
    fft_spectrum = fft_spectrum/spectnum; % to do linear averaging scaling

% one sidded fft spectrum  % Select first half 
    if rem(nfft,2)    % nfft odd
        select = (1:(nfft+1)/2)';
    else
        select = (1:nfft/2+1)';
    end
fft_spectrum = fft_spectrum(select,:);
freq_vector = (select - 1)*Fs/nfft;
end

[studentmatlaber]

thank you so much for your help.

[Mathieu NOE]

you're welcome