JT Ferrara
Followers: 0 Following: 0
Statistics
0 Questions
17 Answers
RANK
1,087
of 295,527
REPUTATION
66
CONTRIBUTIONS
0 Questions
17 Answers
ANSWER ACCEPTANCE
0.00%
VOTES RECEIVED
11
RANK
of 20,242
REPUTATION
N/A
AVERAGE RATING
0.00
CONTRIBUTIONS
0 Files
DOWNLOADS
0
ALL TIME DOWNLOADS
0
RANK
of 154,057
CONTRIBUTIONS
0 Problems
0 Solutions
SCORE
0
NUMBER OF BADGES
0
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Highlights
AVERAGE NO. OF LIKES
Feeds
Multiple IOSTANDARDs for a single HDL coder interface
You can define IOPadConstraint in one of two ways: The same IOPadConstraint for all pins in the interface. For this case, use a...
11 months ago | 1
| accepted
sending complex signal through AXI-lite
Hi Hassan, HDL Coder does not currently support sending complex data over AXI4-Lite directly. As a workaround, you can split th...
3 years ago | 0
Multiple outputs from HDL block in simulink
Hi Muhammad, HDL Coder supports generating an IP core with multiple AXI4-Stream channels. There are two ways to generate such a...
3 years ago | 1
| accepted
Control the gain variable inside the generated IP block
Hi Anoop, This can be accomplished in two different ways: 1) Define a tunable parameter for your gain block, then map this tun...
3 years ago | 0
| accepted
How to deploy the interface model to SD card of Xilinx Zynq ZCU102 kit so that it will run everytime I power up my hardware ?
Please check out this MATLAB Answers post on this topic: https://www.mathworks.com/matlabcentral/answers/474175-how-do-i-deploy...
3 years ago | 0
| accepted
No system or file called 'axiinterfacelib' found
You can also bypass this error message by unchecking the box for "Generate Software Interface Model" in Task 4.2.
3 years ago | 3
Processor and FPGA Synchronization in Coprocessing Mode
Hi Joaquin, When you select "Coprocessing -- Blocking mode", HDL Coder generates two synchronization registers in your IP core ...
3 years ago | 0
| accepted
How do I assign external ports in the Workflow Advisor for the ADRV9361-Z7035 evaluation board mounted on the ADRV1-CRR-BOB
Hi Christian, Based on your description, it sounds like you are correctly specifying the external ports. Can you please check t...
3 years ago | 0
| accepted
When mapping Input/Output data vector port to AXI4-Stream, Is there any way to enter 32-bit width data while using IP Core Generation workflow?
Hi Omer, There are two modeling styles you can use when mapping to an AXI4-Stream interface: (Sample-based modeling) Model the...
3 years ago | 0
HDL-Coder AXI-Vector Strobe Register validation model
Hi Tobias, The validation model generated by HDL Coder only compares the original DUT model against changes due to area and tim...
4 years ago | 1
| accepted
mw_setbook command not found
The "mw_setboot" command is part of the MathWorks Linux image that comes with one of the following Embedded Coder hardware suppo...
5 years ago | 0
Rate transitions and HDL generation port requirement
Hi Michael, The error you are encountering is due to the input ports (which are connected to the AXI4-Stream Slave interface) r...
5 years ago | 0
| accepted
Required Linux image / utilitys for IntelSoC custom boards
Hi Dominique, The default programming method over the HPS assumes you are using the Mathworks Embedded Coder Linux image. Since...
5 years ago | 1
| accepted
How do I specify an FPGA output as interrupt source for the ARM processor in Zedboard
Hi Klaus, FPGA generated interrupts are not currently supported out-of-the-box, but can be accomplished by connecting a DUT por...
5 years ago | 2
| accepted
Is there a compatibility for the Dalsa Xtium-cl mx 4 frame grabber card under development
Hi James, The R2018b release of MATLAB is now available, and with it Teledyne DALSA Sapera support now uses driver version 8....
6 years ago | 1
Can I use The following Bluetooth adapter to connect the mambo mini drone to matlab?
Hi Luis, Compatible Bluetooth adapters for the PARROT Mambo must use the CSR Bluetooth stack, which your device does. The dev...
6 years ago | 0
How to create, connect and use a ni visa device in Matlab?
Hi Pirmin, The value for "rsrcname" is the resource name for the VISA instrument. The format for resource name depends on the...
6 years ago | 1
| accepted