Pemendra Kumar Pardhi
Shri G. S. Institute of Technology & Science Indore
Statistics
RANK
862
of 258,047
REPUTATION
65
CONTRIBUTIONS
11 Questions
39 Answers
ANSWER ACCEPTANCE
45.45%
VOTES RECEIVED
12
RANK
3,707 of 17,783
REPUTATION
361
AVERAGE RATING
5.00
CONTRIBUTIONS
6 Files
DOWNLOADS
139
ALL TIME DOWNLOADS
2937
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Highlights
AVERAGE NO. OF LIKES
Content Feed
link a full bridge DC/AC to an induction machine
Hello ayoub reffai, In your model you need to connected dc supply for converting DC to AC you have used only voltage and cur...
20 days ago | 0
Why does differentiating PID feedback break the system?
Hello Janith Wijekoon With increasing sampling time signal gose to nearly continues time mode which requires large memory. More...
22 days ago | 0
how to do pole to ground fault analysis on dc transmission line
Hi, You can provide pole to ground fault on dc transmission line with the help of circuit breaker connecting between pole and g...
1 month ago | 0
Where is Switch (Relay) in Simulink?
Hi, You can use two breaker in place of a switch and provide it's external control. To charge the chapacitor one circuit break...
2 months ago | 0
How do I encode to a TMS320F28335 and see PWM signals live?
Hello ryan, As per your comment, you are able to run the model in external mode,then general the pwm signals As given below...
2 months ago | 0
Exporting code to CCS, is their any way to observe input adc signal in CCS?
Hi, To observe the ADC input signal of the DSP launchpad on CCS, pls provide a test point to the signals. After that in CCS fol...
2 months ago | 0
| accepted
Non-linear loads
Hello Mohammed Yakoob, For above you need to use MATLAB Simulink, in Simulink you can devoloped model as atteched picture file....
2 months ago | 1
| accepted
How to generate deadband between two complimentary pulses of inverter.
Hi, In MATLAB Simulink, deadband can be provided by using dead zone or on/off delay (continuous) or on/off delay (discrete). I...
2 months ago | 0
Slow simulation of PV system
Hello zenebe, If your system is complex and modelled modelled in continues time domain, then systems performance slow. To mak...
3 months ago | 0
Why is the settling value of my TF so high when compared to my output value? How can I resolve this?
Hello Samuel Pappalardo Firstly, form your second order characteristics experience in standard form S^2+ 2*zeta*w+ w^2=0 For ...
3 months ago | 0
how to connect converter circuit devices each other in matlab simulink ?
Some ideas can be obtained from give model as given below link Pemendra Kumar Pardhi (2022). Zeta Converter Based Led Drive...
3 months ago | 0
how to connect converter circuit devices each other in matlab simulink ?
Hello, Ali Zulfikaroglu The pulse generator output can not connect with the power terminal of any elements (eg. Switch, induc...
3 months ago | 0
| accepted
introduce dead band time for a complementary signal in TI processor
Hello venkata Kumar, Can you share your Epwm A and Epwm B screenshot. I thik you are obtained just inverted Signal fron EPWM...
4 months ago | 0
What does these two block in mppt represent?
Hi noble, Fist block represent to unit delay and second block is reapitive sequence generator. The mppt block provides an a...
5 months ago | 0
F28379D Embedded coder_Sawtooth Wave generation
Hello Raja, To generate sawtooth and triangular waveform, You can try using the Discrete-time alternatives for Repeating Sequ...
6 months ago | 1
PV ARRay Didoe Rsh Error
Hi, Haris Lateef Chaudhary To resolve this isses, double clik on PV array and go into the advanced, chek the box of break the ...
6 months ago | 0
Question
Debug Server Scripting (DSS) error:
Hello, i am trying to interface TMS320F2812 dsp trainer kit with MATLAB 2020b It successfully creates a .out file. However i...
9 months ago | 0 answers | 0
0
answersSubmitted
Zeta Converter Based Led Driver Circuit
This circuit is simulated on sim electronics
9 months ago | 7 downloads |

Model simulink block connection with different simscape
Dear You can connect single phase voltage source from simelectrical-specialized technology- source. In between port 1 and 2 a...
9 months ago | 1
How to set universal bridge as inverter
Hi, Frank You can use universal bridge as a Inverter or PWM rectifier or uncontrolled rectifier For inverter you must select c...
11 months ago | 0
Simscape powergui - Invalid dimension specified for input port
Hi Abd Al-Rahman Al-Remal This error occurs due to, you are providing 6 input signals on gate signal of each IGBT, moreover on...
11 months ago | 1
| accepted
Simulink asynchronous generator voltage input clarification
Hello Dear Abd Al-Rahman Al-Remal The DFIG in wind energy conversion system worked as generator. Therefore it is able to...
11 months ago | 1
Submitted
Grid-Tied Single Phase Solar Photovoltaic Supply System
This project proposes the control of grid-tied single phase solar photovoltaic supply system (including grid synchronization and...
11 months ago | 45 downloads |

Question
Code Generation for TMS320F28379D using MATLAB With Repeating Sequence and Relational Operators block.
Hello, I am trying to generate the code from MATLAB 2020a for the LaunchPad TMS320F28379D microcontroller as shown in the attac...
11 months ago | 1 answer | 1
1
answerError in PWM Generator Vienna Rectifier
Dear Arkadeep Deb Please used datatype conversion with boolean in place of intiger 8 (int 8) I think it may creat a problems. ...
12 months ago | 0
Can anyone help me to solve this error?
Dear Shankarao Rajasuriyan It is occur due to Numbers of signal input in the multiplication/division block After Mux block t...
12 months ago | 0
Why MATLAB crashed while running PV based boost converter simulink model
Dear, This kind of problem rarely occurs. And it occurs due to improper design of system parameters ( Such as inductive or Cap...
12 months ago | 0
| accepted
Stator Flux Estimation of Induction Motor in real time
If any one suffer with above problems It is occurring due to DC ofset in sensed quantity ( it is due to sensor's inherently pro...
12 months ago | 0
| accepted
can't connect source generator with controlled voltage source in matlab simulink
Both elements belong to different libraries. to connect both of them please use simulink to physical connector as attached fil...
1 year ago | 1
| accepted
Question
Data Plotting in a Single Figure
Dear all, I want to plot a single figure including four variable. I have a data as atteched file I want to plot a figure i...
1 year ago | 1 answer | 0