Javier Gazzarri

Last seen: 7 days ago | Active since 2014

Followers: 11 Following: 0

Message

Statistics

All

Feeds

Answered
The thermal port for the battery seems to be not modeled using the code.
Hello Umesh, I cannot find the battery pack definition in your code above. I see you defined a module assembly but not a pack. ...

7 months ago | 0

Answered
How do we determine length and width of Pack object in Battery Builder?
Hello Son, Say you have a battery object called Battery. You can access these properties by typing: Battery.XExtent Battery.Y...

7 months ago | 0

| accepted

Answered
Using Coulomb Counting Method for SoC Estimation of battery
Hello Ranish. Please bear in mind that the above calculation is only valid under the approximation that the voltage is constant...

7 months ago | 0

| accepted

Answered
Battery Charging and Discharging
Hello Mohamad, Would something like this Current Profile be what you are looking for? Battery State-of-Charge Estimation - MAT...

7 months ago | 0

Answered
Simscape Battery Block Parameterization Manager: Datasheet Derived Values for Terminal Resistance R0 of Molicel Battery Cell
Hello Fynn-Brian Thank you for your question. The internal resistance is calculated based on pairs of constant current discha...

7 months ago | 0

| accepted

Answered
Parameter estimation. Different temperature values
Hi Elvir, No, you don't need to worry about that. The isothermal simulation does not need any temperature setting on your part....

10 months ago | 0

Answered
Parameter estimation. Different temperature values
Hi Elvir, The parameter estimation procedure is intended to be used on an isothermal experiment. The results you obtain are, th...

10 months ago | 0

Answered
Li-ion battery pack aging
Hello Nalla, Please consider using the passive balancing block in Simscape Battery. Connecting this to the battery pack will be...

1 year ago | 0

Answered
Li-ion battery R0 value
Hello Nalla, The R0 growth will depend on the type of cell, operating and environmental conditions. It is information you need ...

1 year ago | 0

Answered
Run Current Profiles on a cell and only receive simulated results
Hi Katarina, Certainly. If you need to run one or several current profiles through your model, please connect a controlled curr...

1 year ago | 0

Answered
Run Current Profiles on a cell and only receive simulated results
Hello Katarina, The task you are describing is the validation of the estimated parameters. You need to specify the validation c...

1 year ago | 0

Answered
Causality for FMU in simscape electrical : how to separate an electrical conserving port into 2 physical or simulink signal ports to create an FMU with it.
Hello Enzo, Do you want to create an FMU block for both components connected in series, or one FMU block for each of them? In...

1 year ago | 0

Answered
How to debug .ssc file for custom simscape component
Hello Sudhanshu, Hitesh, The equivalent to a breakpoint is not possible in Simscape because the code in an ssc file is not exec...

1 year ago | 0

Answered
Cell balancing of Li-on battery
Hello Nalla, When I run your model I can see the temperature output (please make sure you enable temperature effects) and the c...

1 year ago | 0

Answered
Setting Aging parameters in generic battery model (battery mask)
Hello Jarin, Aging parameters are typically difficult to find in datasheets and sometimes you need to cycle the battery to find...

1 year ago | 0

Answered
Choosing a machine learning model for predicting the results of a process
Hello Fabian, Great use case for Machine Learning. In MATLAB you can actually try several ML algorithms simultaneously and pic...

1 year ago | 0

Answered
Battery builder in Simscape question
Hello Bacel, You can do this by defining the cell, defining a parallel assembly of just one cell, and then creating a module o...

1 year ago | 0

Answered
Simulate 1 hour SOC of the Generic Model Simscape Electrical Battery in 1 second
Hello Haad, In this case I would convert all units in all block parameters to hours instead of seconds. Depending on the case, ...

1 year ago | 1

| accepted

Answered
How is "power_dissipated" being calculated when linking a Probe block to a Battery (Table - Based) block?
Hello Jose, I believe this is because the default units for power dissipation is kW as opposed to W. You can see this when you ...

1 year ago | 0

| accepted

Answered
Using Simscape Model (code generated or just protected) to run Simulation on PC with just Matlab/Simulink
Hi Hitesh, Yes, you don't need to create a project for this. From the top level of the model, please go to: SAVE -> Standalone...

1 year ago | 0

Answered
Using Simscape Model (code generated or just protected) to run Simulation on PC with just Matlab/Simulink
Hello Hitesh. This is indeed possible and there are a couple of options: 1) Create a Protected Model Reference as described her...

1 year ago | 0

Answered
Simulate 1 hour SOC of the Generic Model Simscape Electrical Battery in 1 second
Hello Haad, I see two options: 1- You can scale everything that is linear so that 1sec simulation = 1h real time. For the batt...

1 year ago | 1

Answered
How to correctly estimate simulation time and error in a battery cell simulation
Hello Jorge, Your statement about error and simulation time is correct. However, if the model is simple (e.g. it only has a sin...

1 year ago | 0

Answered
Curve-fitting of measured and simulated equivalent circuit impedance to find R/C values.
Hello Aditya, You can use Optimization Toolbox to fit a R0 + 2RC equivalent circuit to an impedance spectrum as long as this is...

1 year ago | 0

Answered
Simulate 1 hour SOC of the Generic Model Simscape Electrical Battery in 1 second
Hello Haad, I am not sure I understand the 1sec = 1hour statement. The battery capacity in the block is entered in Ah, so you ...

1 year ago | 1

Answered
Warnings in Simscape battery for Cell Balancing
Hello Manoj, Can you please give me a few more details about the battery cell you are modeling? What is the maximim voltage for...

1 year ago | 0

| accepted

Answered
How to set initial SOC value in simscape 1RC or 2RC equivalent circuit model (Lithim-Ion-Battery)
Hello Jassir, You are correct. Qe_init (charge deficit) is where you can set initial SOC. Please take into account that Qe has ...

1 year ago | 1

| accepted

Answered
Assertion error in battery pack cooling system implementation
Hello Ali, Can you please check if you are using the same current sign convention we do in the block? In many cases I see this ...

1 year ago | 0

| accepted

Answered
Is there a way to reset the simscape battery model during simulation?
Hello Maximilian, Would you kindly provide the current profile you are using? SOC is calculated integrating current and dividin...

2 years ago | 0

Answered
What is the nominal parameters of the battery used in "Lithium Battery Cell - Two RC" model? and the type of the battery model?
Hello Vikas, The parameterization of the battery cell in this example is done as a function of SOC and temperature with a grid ...

2 years ago | 0

Javier Gazzarri

Statistics

MATLAB Answers

MATLAB Answers

File Exchange

File Exchange

File Exchange

File Exchange

MATLAB Answers

MATLAB Answers

MATLAB Answers

Feeds