Community Profile

photo

Joel Van Sickel


Last seen: 2 days ago

MathWorks

200 total contributions since 2020

Contact

Joel Van Sickel's Badges

  • First Submission
  • GitHub Submissions Level 1
  • 6 Month Streak
  • Knowledgeable Level 3
  • Revival Level 4
  • First Review
  • First Answer

View details...

Contributions in
View by

Submitted


Model-Interaction-Examples-Live-Editor-and-Simulink
Some simple examples to show ways set up models to interact between the Live Editor and Simulink and Simscape models.

3 days ago | 0 downloads |

Answered
Is there any Simulink model for EV to show how to use Brake Resistor in the system?
Hello Atrin, do you mean brake resistor? In that case, you can use the standard resistor for that. https://www.mathworks.com/...

4 days ago | 0

Answered
Is there any Simulink model for Electric Vehicles to show how to use super capacitor in the system?
Hello Atrin, please start here: https://www.mathworks.com/help/physmod/sps/ref/supercapacitor.html and here: https://www.mathw...

4 days ago | 0

Answered
mathematical model development of regenerative thermal oxidizer for volatile organic compounds
Hello Omkar, the gas elements are for modelling the dynamics of a gas system, not it's chemical reactions. This particular dom...

4 days ago | 0

Answered
How to correct this error for simulating this changed IEEE 14 bus.
Hello Sango, please start by following the recomendations in the error message. In this case, addiding snubber resistors (make...

8 days ago | 1

| accepted

Answered
Optimisation using a simulink model called from inside a MATLAB function
Hello Hamidreza, one of the issues is that you need to make sure that the initial iterations perturb the system enough that the...

10 days ago | 0

Answered
How to simulate PMU in WAMS Techanology
Hello Krishan, please start with simscape electrical - specialized power systems. They have a number of functions to help with...

10 days ago | 0

Answered
how to design bldc motor drive of 3200 rpm at 48v 18A
Hello Muhammad, that is a very open ended problem to which there is no one correct answer. Please start with this page as a re...

10 days ago | 0

Answered
How to calculate total harmonic distortion for a given signal?
Hello Millo, when you used the function, did you only provide the signal data, or did you provide attitional parameters? It is...

10 days ago | 0

| accepted

Answered
Problems with multirate simscape electrical model
Hello Ander, you can have seperate step sizes for your solver configurations. This is what it should look like: (I set one to ...

10 days ago | 0

| accepted

Answered
The following two blocks cannot be connected in series because they are modeled as current sources:
Hello Sreeraj, if you are seeing impact with the snubber, I would recommend increasing the size of the snubber. Maybe try some...

23 days ago | 0

Answered
Error: "Each physical network must be connected to exactly one Solver Configuration block. There is no Solver Configuration block connected to Physical Network with the following blocks..."
Hello, the solver configuration block is a simscape block under utilities that you can connect to any part of your simscape net...

23 days ago | 1

Answered
Shared simulation shows different results
Hello Alexandra, the easiest explanation for this would be if you are using library blocks and somehow one of you have differen...

25 days ago | 0

Answered
OPC connection with siemens TIA portal
Hello Omkar, it is quite possible the problem isn't with this code itself. As this is just a function, the question is where i...

25 days ago | 0

Answered
Optimizing Simscape Generated Code
Hello Sean, code generation for simscape should not be causing a slow down like this. It is often used for real-time tasks whe...

1 month ago | 0

Answered
The model has changed between the time when two instances of this model were compiled. This is not allowed for models referenced in Normal Mode.
Hello Xu, since the model was copied and that is cauisng the problem, I would try to build the model conversion block by hand. ...

1 month ago | 0

| accepted

Answered
Constant Power Load (CPL) block Simscape Electrical
Hello Krupa, you can build your own constant power load using a controlled source. use a controlled current source and calcula...

1 month ago | 1

Answered
Matlab code for voltage regulation
Hello Ayaz, Matlab has code for implementing genetic algorithsm to optimize cost functions. You will need to choose your cost ...

2 months ago | 1

Answered
How to create a custom block for calculating RMS of a signal?
Hello Krish, here is information on using matlab functions to work in Simulink. https://www.mathworks.com/help/simulink/ug/cre...

2 months ago | 0

Answered
I'm charging a 40V, 50Ah Lead acid battery using buck converter and PI control on battery voltage and current. Simulink 2012b hangs after half an hour of simulation maybe because of data storage. Please suggest me what can be done.
Hello Ravindra, please update to a newer version of matlab, and utilize simscape components. Start here: https://www.mathworks...

2 months ago | 0

Answered
if anyone having dynamic data for IEEE 24 and IEEE-30 bus system can u send me .
Hello Abuvatamizhan, unfortunately this question does not involve MathWorks tools and should be asked in other venues. Regards...

2 months ago | 0

Answered
Varying power demand with TimeSeries data & Ending a system
Hello KahHin, using the dynamicl load block is the correct way. Why do you say it doesn't work? Use the three phase one and s...

2 months ago | 0

Answered
Current loop for phase shift dc/ac full bridge
Hello Vincenzo, the easiest way to control phase shifting of your pwm is to create your own pwm generator using a resetable int...

2 months ago | 0

Answered
What is more suitable to interface SimPowerSystems battery with Simscape, a Current-Voltage Simscape interface or a Voltage-Current interface?
Hello Saif, neither is better or worse than other and totally dependent on your specific toplogy. In general, if your output i...

2 months ago | 0

Answered
Is there an example that demonstrates how to build a three phase transformer with extended delta in the primary, Wye in secondary , delta in tertiary
Hello Enock, there are numerous transformers that have been added to the simscape electrical library that support various confi...

2 months ago | 0

Answered
How do I multiplex 3 phase power system signals onto a single signal or generate a varying frequency voltage source
Hello Ciaran, the specialized power systems (specialized technology/simpowersystems) blocks do not support single line wiring. ...

2 months ago | 0

Answered
How to use simulink to find frequency response (Gain vs frequency) of Rc low pass filter ?
I am just moving Mouhammed's answer down here to mark the question as answered: Mouhamed Niasse on 21 Sep 2020 at 13:44 The ...

2 months ago | 0

Answered
How to use simulink to find square wave in op Amp circuit ?
Hello Wann, there are numerous square wave generator topologies that can be used. You can google search to investigate them an...

2 months ago | 0

| accepted

Answered
How can i change the output power of a wind turbine induction generator in simpowersystems, and how can I measure the output power?
Hello Qais, you will also need to increase the power delivered to the motor. This will show up in the simulation as increase v...

2 months ago | 0

Answered
I dont find any windings in the asynchronous machine block. Is there any way of altering the resistance of stator phases?
Hello Shivakumar, while you cannot change the resistance of a single phase in the model, you can add resistance to one of phas...

2 months ago | 0

Load more