Answered
Is there a way to simulate or represent the two layers of the stator windig?
You can place another winding in series with the magnetic domain wire (purple wire, N S) so that they are both seeing the same m...

5 months ago | 0

| accepted

Answered
Unexpectedly High 'id' Current Value in N-Channel MOSFET Simulation using Simulink
Hello, I tried recreating your simulation and got a current of 800 amps, which while not your 16000, is still quite high. Have ...

5 months ago | 0

| accepted

Answered
How can i add an equation to a block (impedance measurement)?
You have 2 options. If it is a static value of impedance, you can pre calculate your circuit parameters such as R = R_pu*Length...

5 months ago | 0

Answered
Is it possible to model a john bedini motor ?
You can do that using the simscape electrical tool. There is free training to get started: https://matlabacademy.mathworks.com/...

5 months ago | 0

Answered
Voltage Swell from Signal Builder
You can hook the signal builder block into a controlled voltage source.

5 months ago | 0

Answered
Simulink Load Flow Analysis for Electric Fleet Charging Station
Load flow for this tool was designed specifically for AC systems. While it does support single phase and unbalanced lines, this...

5 months ago | 0

Answered
unbalanced load on a synchronous generator
I tested these blocks and they don't seem to work well when split into a three phase load like this (even for a balanced load). ...

5 months ago | 0

Answered
tapping of secondary delta transformer
Please look at this block as a starting point: https://www.mathworks.com/help/sps/ref/tapchangingtransformer.html you can get f...

5 months ago | 0

Answered
Hello. If I have included delays in my code for my controller, how do I implement it so that the delays are considered when the code is executed?
The correct way to simulate a digital controller, so that you are incorporating the delay of the digital system is to utilize so...

5 months ago | 0

Answered
Breakdown Voltage (BDV) Tester for Transformer Oil
Hello Hatim, you don't actually ask a question or share model details. If you still want help, please ask a specific question ...

5 months ago | 0

Answered
While Opearting a N channel MOSFET in MATLAB with 100VDC, 100 Ohm load. the MOSFET only allowing 0.2A in each condition but I am expecting of 1A.
Increasing the mosfet threshold voltage will make it conduct less, not more. You need to parameterize the mosfet correctly. In...

5 months ago | 0

Answered
How can I create a simulation that supplies power to the motor by connecting fuel cells, dc-dc converters, and supercapacitors?
This really depends on how much detail you need for the converter. In general, when doing powertrain analysis, you don't need t...

5 months ago | 0

Answered
Different Thyristor Gate width gives different waveforms.
Are you sure the results are wrong? You don't have a dc-link capacitor to maintain the dc voltage and with the inductive load a...

6 months ago | 0

Answered
Better solver for simscape power electronics simulation
You can set your absolute tolerance to be the same as your relative tolerance, and uncheck the option for absolute tolerance. T...

7 months ago | 0

Answered
Table based battery block choices
You need to have either Simscape Battery or Simscape Electrical installed to have access to the table based battery. Please see...

7 months ago | 0

Answered
Inconsistent results when simulating an LC series circuit with SimScape
He issue is that the Adams solver is specifially for non-stiff problems and your problem being in simscape is typically a stiff ...

8 months ago | 0

Answered
Error while running Simulink
This happens when a model has extermely small time constants or challenging equations to solve. That usually means the model is...

8 months ago | 0

Answered
Thermofluid simulation of an electric motor
This is one starting point: https://www.mathworks.com/help/simscape/ug/motor-thermal-circuit.html and here is another: https://...

8 months ago | 0

Answered
sic mosfet SPICE models.lib file into Simulink using subcircuit2ssc
Wolfspeed specifically provides LTspice models which use a proprietary interface that is not always compatible with base SPICE. ...

8 months ago | 0

Answered
Exporting a simulink/Mathlab model as a circuit element for simulation software (Pspice/Cadence)
There are a few options. I am listing them by order of cost (cheapest to most expensive) You can try and utilize the co-simula...

8 months ago | 1

Answered
PV Mppt constant output voltage
the goal of mppt is to get the optimal power extraction of a solar panel. To accomplish this, the voltage and current must vary...

8 months ago | 1

| accepted

Answered
Sample time relation of controller and PWM switching frequecny
Hello, you are correct that the most common approach is to have the switching frequency be the same as the control frequency. ...

8 months ago | 1

Answered
How can I export my Simulink electrical circuit into a Matlab function?
The easiest approach to this would be to utilize the sim() command. This lets you set parameters, run a simulation and then get...

9 months ago | 0

Answered
How can i implement BLDC commutation logic block to a PWM Module?
Please start with this page: https://www.mathworks.com/solutions/electrification/bldc-motor-control.html at the bottom are lin...

9 months ago | 0

| accepted

Answered
Graphs are paused during simulation in Simulink and do not resume once RLC load is added via circuit breaker
It sounds like the simulation is "hanging" aka, it starts taking such small time steps that nothing appears to be happening. Thi...

9 months ago | 0

Answered
How can I connect my dynamic (mathematical) model of inverter to the grid simulink model?
the most common way to to attatch it to controlled voltage sources for the inverter output and use a controlled current source f...

10 months ago | 0

Answered
Slip in Asynchronous Block - Induction Machine Squirrel Cage
the block can only give you input for the initial condition of slip, but this does not determine your slip once the model is run...

10 months ago | 0

| accepted

Answered
How the voltage based active cell balancing model works for larger voltage difference and not working for smaller voltage difference ?
You are modelling lithium ion batteries and giving them different nominal voltages. These batteries are not linear and would no...

10 months ago | 0

Answered
unable to resolve cooling plate error
I think you need to set your number of nodes to 14 and not 14x14 for the cooling plate. If that doesn't solve it, please share ...

10 months ago | 0

| accepted

Answered
How to import .SUBCKT Spice model into MATLAB Simscape?
Unfortunately, there is no guarentee that an imported pspice model will work in simscape. It sounds like you used the command c...

10 months ago | 0

Load more